EXF OPTICALNetwork components Project brief
Optical reference library

Frequent up down of access switch interfaces

Frequent up down of access switch interfaces
Illustrative equipment reference
Download PDF
Article contents

Frequent status changes from up to down or vice versa in the ports logged by the switch port syslog indicates a port flap. I have checked many switches that are located in different buildings and these had same kind of logs! the port is going down for like 2 seconds and up again why is this happening? two switches are doing this. My company is using IPT phones model CP-7821 For the past 2 weeks we've been noticing some strange behaviors with certain phones.

Once plugged they display "Network Unavailable" and if we take a look into the switch interface and keeps changing from up to down (connected/notconnect). These ports are most. Port flapping, also known as link flapping, causes a switch port's state to fluctuate between up and down within concise periods of time.

For example, two links work in primary/backup mode. The building is a few months old so I don't really have a baseline for what is normal. I'm noticing that in the logs of my WS-C3650-12X48UR-L and ws-c2960x-48lpd-l that some of the access ports are frequently going.

From reference to enquiry

Questions for your project

Use these editorial prompts alongside the linked excerpts. They identify items to confirm for your project.

Detailed reading

Distribution and installation references

Solved: Switchport goes up and down

For the past 2 weeks we''ve been noticing some strange behaviors with certain phones...Once plugged they display "Network Unavailable" and if we take a look into the switch

Port Flapping: Causes, Troubleshooting, and Prevention

Port flapping is a network problem where a port continuously switches on and off (up and down), causing instability. The overwhelming amount of packet loss and increased latency due to this constant rate

Port flapping — Definition, common causes, and troubleshoot

Frequent status changes from up to down or vice versa in the ports logged by the switch port syslog indicates a port flap. Network admins can use this file to easily identify the specific port and its

Configuring Link Flapping Protection

A link flap occurs when the physical status of an interface frequently alternates between Up and Down due to network flapping or network cable faults. This causes frequent network topology changes and

Access Interfaces Frequent up/down : r/Cisco

You can probably run a tdr cable test from the switch. If the cable checks out then I would test the port with a different device to make sure it''s not an issue with the switch port.

Network Switch Troubleshooting Guide: Common Problems and

A comprehensive switch troubleshooting from the physical layer to the data link layer to the network layer to find out why your network switch is not working.

What is Network Flapping? Causes, Fixes, and Explanations

What is network flapping? Network flapping is the rapid fluctuation of network routes or interfaces between an up (active) and down (inactive) state. This constant change disturbs the

Troubleshooting Interfaces

There are a number of possible interface issues that could occur on Cisco routers and switches. This lesson explains how to find and fix them.

How to monitor and send an alert when an interface port is flapping?

Spectrum allows you to generate an alarm when the interface goes up and down frequently. In that case, Spectrum generates a lot of bad link alarms but it is cleared when the

Interface goes up and down

I got many users complaining that they are loosing the connection very often. Here is the logging! From one switch which shows what happens, the same port is going up and down many

An Ethernet Interface Frequently Alternates Between Up and Down

This document describes the principles and configurations of interfaces and provides configuration examples.

Interfaces on a Cisco SG500 goes up and down

Dear Cisco users, I have a annoying problem with two of SG500 switches. Some of the switch ports go automatically down and after two seconds the go up. See attached file Some more

Troubleshooting network interface flapping

Issue Description Network interfaces are flapping Frequent log messages similar to the following in /var/log/ltm: info bcm56xxd : 012c0015:6: Link: is DOWN info bcm56xxd :

Switch Port Flapping

Looked at system log and port connected to main switch flaps for a few seconds every 5 or 10 minutes then eventually goes down; comes back up on its own after random period of time.

Switch is increasing input errors for a Down interface

Hello Cisco Team, I have a switch that is increasing the input error for an interface in Down status. Below you will fin some data about this interface. The switch is

Configuring an Interface to Transit to the Error-Down State When a

If the number of link flappings on an interface reaches the threshold within a link flapping period, the system disables the interface and records its status as ERROR DOWN (link-flap). By

Switch port flaps up and down endlessly when PC connected go to sleep

Dear Community, Hope everything is great, I am a network administrator and recently i faced a very strange behavior. In one of our customer''s switches (C9300-48P-A), when the PC

what causes flapping of uplink interfaces on a Cisco switch

Link flap means that the interface continually goes up and down in a Cisco Switch. The interface is put into the errdisabled state if it flaps more than five times in 10 seconds.

Related Video Reference

This video was associated with the source search result. Verify technical details against current product documentation and project requirements.

Discuss your network project

Share the route, interfaces, cable or port requirements and acceptance scope.

Start a Project Enquiry