EXF OPTICALNetwork components Project brief
Optical reference library

Methods for using purple tubing for optical fiber cables

Methods for using purple tubing for optical fiber cables
Illustrative equipment reference
Download PDF
Article contents

Purple PEEK tubing is used to protect and route optical fiber cables while maintaining bend radius and facilitating identification in complex installations.

Overview of Purple Tubing

Purple tubing, often made from PEEK (polyether ether ketone), is a high-performance, convoluted tubing system designed for optical fiber protection in harsh environments. It provides mechanical protection, chemical resistance, and flexibility while allowing easy routing of fiber cables in aerospace, industrial, and telecommunications applications. The color coding (purple) also helps in identifying specific fiber paths or cable types according to TIA-598-C standards.

Installation Methods1.

Pulling Fiber Through Tubing

Use a figure-eight coiling method when unspooling fiber to prevent kinking and torsion. Ensure the pulling tension does not exceed the cable's maximum tensile rating; for most loose tube cables, this is around 600 lbF (2,700 N),. Employ low-elasticity pull lines such as aramid yarn or wire rope to minimize tension fluctuations during long pulls.

Lubrication may be applied to the tubing to reduce friction and prevent damage to the fiber during installation. 2.

Maintaining Bend Radius

Respect the minimum bend radius of both the fiber and the tubing.

For PEE

K tubing, the convoluted design allows flexibility, but the fiber inside should not be bent below its specified radius. When routing around corners or through conduits, use gentle curves and avoid sharp bends to prevent signal loss or fiber breakage. 3.

Securing and Routing

Clamp tubing at frequent intervals to prevent sagging and movement, especially in vertical installations. Use innerducts or conduits for additional protection in outdoor or high-traffic areas. Color-coded tubing simplifies fiber identification and reduces the risk of misconnections during splicing or maintenance.

4.

Coiling and Storage

For temporary storage or handling, coil fiber in figure-eight loops of 5–8 ft (1. 5–2. 4 m) diameter to relieve mechanical stress.

Avoid continuous coiling in one direction for long lengths, as this can introduce torsion and damage the fiber. 5.

Inspection and Reinstallation

If tubing is removed for inspection, reinstall it exactly as supplied before placing the fiber back in service. Ensure the tubing is free of debris and properly aligned to prevent abrasion or microbending.

Best Practices

Always follow manufacturer specifications for tubing dimensions, bend radius, and tensile limits. Use purple tubing consistently for specific fiber types or routes to maintain clarity in complex networks. Combine tubing with strain relief boots or connectors that match the fiber color code to ensure consistent identification throughout the system.

By following these methods, purple PEEK tubing can effectively protect optical fibers, simplify identification, and ensure reliable long-term performance in both indoor and outdoor installations.

ALTOS® Figure-8 Loose Tube, Gel-Free Cable | CorningCorning ALTOS® figure-8 gel-free cables are self-supporting aerial cables designed for easy and economi.

From reference to enquiry

Questions for your project

Use these editorial prompts alongside the linked excerpts. They identify items to confirm for your project.

Detailed reading

Distribution and installation references

ALTOS® Figure-8 Loose Tube, Gel-Free Cable | Corning

Corning ALTOS® figure-8 gel-free cables are self-supporting aerial cables designed for easy and economical one-step installation. The loose tube design provides

Purple Peek Fiber Optic Convoluted Tubing System

Special-purpose PEEK convoluted tubing and lightweight, durable composite thermoplastic accessories—color-coded purple for aerospace fiber optic interconnect systems

Optical Fibre Manufacturing Process

Optical Fibre Cable Manufacturing ProcessSZ-stranding3 CollapseOptical Fibre and Cable TestingOptical fibres in a cable are normally protected in one of two ways, either being tight buffered or contained in loose tubes. When tight buffered the individual optical fibre is covered directly with a layer of thermoplastic material or one or more fibres can be contained within a loose tube which is filled with a thixotropic gel. These processes a...See more on pongsak.ee.engr.tu.ac.thFiber Optic Center

Furcation Tubing Selection Guide - Fiber Optic Center

Explore fiber optic furcation tubing types for protecting and organizing sensitive fibers. Styles available for splicing, termination, and connection needs.

Optical Fiber Installation Methods – MapYourTech

This comprehensive guide examines all major fiber installation methods, from underground trenching to submarine cable laying, providing technical insights drawn from industry

Duct Installation of Fiber Optic Cable

Do not use automated figure-eight machines when installing fiber optic cables with a central tube design or any loose tube cable having one or more layers of corrugated steel armor.

Optical Fiber Jointing Methods

The document discusses methods for joining optical fibers, including fusion splicing and mechanical splicing. Proper preparation of the fiber ends is important for both methods.

Optical Fiber Cable Optical Fiber Cable In

All Fiber Optic Cable reels should be stored upright Laying the reel on its side may cause damage to the reel flange and/or cause the cable layers to shift – This may cause cable to snag during de-reeling.

Fiber Optic Color Code: The Ultimate TIA-598-C Guide

Master the TIA-598-C fiber optic color code standard. Read our complete guide and use our free interactive calculator to easily identify 1-144 core cables.

Handbook Optical fibres, cables and systems

A PON can be deployed in a FTTH (fibre to the home) architecture or in a FTTB (fibre to the building), a FTTC (fibre to the curb) or a FTTCab (fibre to the cabinet) architecture, depending on local demands.

How To: Install Fiber Optic Cable for Success –

Learn the best practices for installing fiber optic cable, from patch cords to bulk distribution fiber.

Duct Installation of Fiber Optic Cable

As fiber optic cable is sensitive to excessive pulling, bending and crush forces, much care shall be taken to avoid cable damage during its duct installation. Methods of duct installation,

Optical Fiber Installation Methods – MapYourTech

The evolution of fiber optic installation methods mirrors the development of optical communication technology itself. The first commercial fiber optic systems, deployed in the late 1970s

The NEC and Optical Fiber Cable and Raceway Rules | EC&M

Because optical fibers don''t carry current, the normal NEC rules related to ampacity don''t apply — unless, of course, you run them with current-carrying conductors or use a fiber-conductor

Cable Preparation Best Practices for Fiber Optic Indoor/Outdoor

This best practices document is a step-by-step guide for end and midspan access of loose tube optical cable, including sheath removal, core preparation, and fiber preparation.

1166-D02

The optical fiber needs to be trimmed and stripped so that approximately 10 mm of stripped fiber protrudes from both fiber optic connectors. The total length of the optical fiber must also be controlled

101 Guidelines for Fiber Optic Cable Installation

Never directly pull on the fiber itself. Fiber optic cables have Kevlar aramid yarn or a fiberglass rod as their strength member. You should pull on the fiber cable strength members only! Never exceed the

Underground Fiber Optic Cable Installation: A Complete

Learn how to install underground fiber optic cables safely and efficiently. Explore trenching, conduit selection, direct burial methods, splicing,

Indoor and Outdoor Fiber Optic Cable Installation: Key Considerations

Explore best practices for installing indoor and outdoor fiber optic cables, including conduit, direct burial, riser, and aerial applications. Build stable, long-lasting networks.

Discuss your network project

Share the route, interfaces, cable or port requirements and acceptance scope.

Start a Project Enquiry