EXF OPTICALNetwork components Project brief
Optical reference library

Step By Step Spectroscopy Experiment Hands On Guide For Students

Search optical fiber, connectivity, cable management and network infrastructure references.

Step Spectroscopy Experiment
  • Experiment on the characteristics of an adjustable fiber optic attenuator

    Experiment on the characteristics of an adjustable fiber optic attenuator

    A tunable all-fiber optical attenuator (AOA) based on microfiber with adjustable coupling angle is reported and demonstrated. The AOA is fabricated of a microfiber probe coupled to a tapered fiber on th.


  • How to calculate the relay protection step size

    How to calculate the relay protection step size

    Use this Protection Relay Setting Calculator to calculate pickup current, time multiplier settings (TMS), operating time, coordination time interval (CTI), and plug setting multiplier (PSM) using fault current, CT ratio, and IEC 60255 curve parameters. g time intervals to determine when a relay operates. This protection scheme is used for both phase and ground faults, but it uses separate relays for each. Distance relaying is directional and typically utilizes four zones of protection, each of which reaches a fixed distance and operates in a set. of protective relays in terms of protecting high voltage lines. Consequently, it is shown the method of calculation for a particular power line a d performed the calculation for setting the distance protection. The settings are based on: Line impedance (primary & secondary values). Determine the operating time of the upstream relay with the expression t2a = t1 + tmargin.

    [PDF Version]
  • Fiber Optic Communication Lab Experiment

    Fiber Optic Communication Lab Experiment

    This lab offers an immersive, web-based simulator that enables you to explore and experiment with key concepts in optical communication, such as signal transmission, fiber optics, modulation, and detection techniques. Availability of plastic optical fiber (POF) The plastic optical fiber used in some of these experiments is available for science distributors. It is a 1000micron (1mm) POF available from several suppliers. Achieving amplitude modulation of an analog signal, transmitting over fiber, and recovering the original signal. Current (P-I) characteristics and measur rement of numerical aperture of a or lo s by O IC REMENT OF NUMERICAL APERTURE OF A FIBRE AFTER PREPARING To measure the numerical aper, which in turn. Theory: Fiber Optic Link can be used for transmission of analog as well as digital signals. The transmitter module take the input signal in electrical form and then transform it into optical.

    [PDF Version]
  • Pw relay protection experiment

    Pw relay protection experiment

    The study presents a training setup demonstrating real-time fault monitoring and response using digital relays. Experimental results confirm the MICOM P111 meets IEC 60255 standards, ensuring quick and accurate fault isolation. Protective relays are critical in. Protective relays and devices have been developed over 100 years ago to provide “lastline”of defense for the electrical systems. They are intended to quickly identify a fault and isolate it so the balance of the system continue to run under normal conditions. The selection and applications of. Many relays use an electromagnet to mechanically operate a cuits), or where several circuits must excessive values of pow oad release. several times greater than maximum load current. Over-current relays. work and practice problems. Proportional exams feature problems you haven't seen before that are solvable using general principles learned throughout the current and previous courses, for which the only adequate preparation is independent problem solving practice every day.

    [PDF Version]
  • Experimental Objectives and Requirements of Optical Power Meter Experiment

    Experimental Objectives and Requirements of Optical Power Meter Experiment

    EXPERIMENT MEASUREMENT OF OPTICAL POWER USING To objective of this experiment is to measure optical power using optical pmver meter. Procedure : 1. Connect.

    [PDF Version]
  • Wiring Experiment for Power Distribution Box

    Wiring Experiment for Power Distribution Box

    Watch the full process of wiring an electrical distribution panel in this satisfying time-lapse video. The foundational formula is $Power (Watts) = Voltage (Volts) times Current (Amps)$, or $P=V times I$. This. I DONT KNOW ABOUT RULES AND REGULATIONS IN YOUR PROVINCE/TERRITORY/STATE BUT HERE IN PEI, ALL LIGHTS OTHER THAN STOCK HEADLIGHTS/FOGS ARE ILLEGAL TO USE ON THE ROAD. OFF ROAD USE ONLY! This box did not cost me very much if anything at all, being as I had almost everything on hand.


  • Distribution boxes are connected step by step

    Distribution boxes are connected step by step

    How to Install a Cable Distribution Box Safely and Reliable cable distribution boxes ensure safe, efficient power management for residential, commercial, a.

    [PDF Version]
  • Experiment on a 220kV Relay Protection System

    Experiment on a 220kV Relay Protection System

    This project simulates an impedance-type distance relay for protecting a 220 kV transmission line using MATLAB/Simulink. The relay detects faults by measuring line impedance and operates in three zones (Z1, Z2, Z3) with configurable time delays. The simulation includes:After the 220kV substation relay protection training system is adopted, the main work is to teaching the relay protection staff, substation operating staff and direct current equipment maintenance staff technical skills. The simulation includes: -Fault analysis. The paper presents some gained knowledge on customer specification of technical requirements for the integrated protection and control system showing also a typical application in a project involving two 220 kV substations in the Romanian Power Grid.

    [PDF Version]

Discuss your network project

Share the route, interfaces, cable or port requirements and acceptance scope.

Start a Project Enquiry